A Riello burner lockout is a safety stop. The control box has seen something unsafe during start-up or running, so it shuts off the fuel and lights the red lamp in the reset button. Press reset once; if the burner keeps locking out, the cause is usually no flame being detected, low gas or oil supply, a dirty flame sensor or an air pressure switch problem, and it must be found before you reset again.

What does lockout mean on a Riello burner?
Every Riello burner, whether a 40 FS gas burner or a 40 G oil burner, follows a fixed start-up sequence controlled by its control box:
- The fan runs for a pre-purge to clear the combustion chamber.
- The ignition spark starts.
- The gas or oil valve opens.
- The flame must be detected within a short safety time.
If any step fails, the control box stops the burner and locks it. Unlike a normal stop, a lockout does not clear by itself. Someone has to press the reset button.
There is one exception worth knowing. If the burner keeps repeating the start-up cycle without locking out, Riello’s manuals point to gas pressure sitting very close to the setting of the minimum gas pressure switch. That is a supply or adjustment issue rather than a lockout.
Is it safe to keep resetting a Riello burner lockout?
No. Riello’s own instructions say that if the burner runs normally after one reset, the stop was probably a temporary fault. However, more than two resets in a row can damage the installation. On the third lockout, stop and call a qualified technician.
The reason is simple. Each failed attempt can leave unburnt gas or oil in the combustion chamber. Repeated resets therefore increase the risk of a hard, unsafe ignition, and on oil burners they soak the chamber with fuel.
How do you read the Riello lockout blink code?
Newer Riello gas burners have a flame control with built-in diagnostics. When the red lamp is steady, press and hold the reset button for more than 3 seconds. The LED then flashes a pattern; count the blinks between pauses. Not every older control box has this feature, so check the manual for your burner.
| Blinks | What it means | Common causes |
|---|---|---|
| 2 | No flame at the end of the safety time | Air in the gas line, gas valve not opening or passing too little gas, ignition transformer or electrode fault, ionisation probe fault, phase and neutral swapped |
| 3 | Air pressure switch fault | Switch stuck or badly adjusted, not enough air pressure, fan motor fault |
| 4 | False flame signal at start or at stop | Flame signal present when there should be none, leaking valve, probe problem |
| 7 | Flame lost during operation | Low gas pressure, dirty gas filter, probe badly positioned, valve passing too little gas |
| 10 | Wiring error or internal fault | Loose or wrong connections, faulty control box |
Write down the blink count and the moment the lockout happens: during pre-purge, at ignition, or while running. This one note saves a technician a lot of time.
Common causes of Riello burner lockout on gas burners
On 40 FS series gas burners, these are the faults that come up most often:
- Air in the gas line. After new pipework, a meter change or an LPG cylinder changeover, air in the line stops the flame from lighting. The line must be purged properly.
- Low or unstable gas pressure. A drop in PNG supply, an LPG vaporising problem or a blocked gas filter can trip the minimum gas pressure switch.
- Gas valve problems. A weak coil or a valve that opens too little gives a flame that fails to establish. Check the solenoid valve, such as the Brahma EG12 SR GMO gas solenoid valve used on many FS burners.
- Ionisation probe faults. A dirty, cracked or wrongly positioned probe, or a cable touching earth, means the flame is there but not detected. The Riello probe connection for FS5, FS10 and FS20 is a common replacement.
- Phase and neutral swapped. Riello lists inverted phase and neutral as a cause of lockout. This often happens in Indian plants after a panel is rewired.
- Ignition problems. A worn electrode, wrong electrode gap or failing ignition transformer gives a weak or no spark.
- Air side problems. A faulty air pressure switch, a fan motor fault or too much combustion air.
Why does a Riello oil burner lock out?
On 40 G series oil burners, flame detection is done by a photocell instead of a probe. The usual suspects are:
- Dirty or failed photocell. Soot on the photocell blinds it, so the control box thinks there is no flame. A faulty unit such as the Siemens QRB4A photocell needs replacing.
- Photocell seeing false light before start-up, which causes a lockout before ignition.
- Worn or blocked nozzle. A poor spray pattern gives an unstable flame.
- Air in the suction line or a pump that loses prime, often after the tank ran low.
- Dirty filters in the line, the pump or the nozzle.
- Wrong electrode position or too much air for the nozzle size.
What can operators check before calling a technician?
Some basic checks are safe for plant staff. Switch off power before touching anything inside the burner.
- Confirm power supply, fuses and that boiler thermostats or safety limits are not open.
- Check the manual gas cock is open, or that the oil tank has fuel and its valve is open.
- Look at the gas pressure gauge and compare it with the normal reading.
- On oil burners, pull out the photocell and wipe it gently with a clean dry cloth.
- Make sure the plugs on the control box are fully pushed in.
- Note the blink code and when the lockout happens.
Never bridge control box terminals, bypass pressure switches or open the gas train yourself. Those jobs need a qualified technician with a combustion analyser.
Finally, if the same Riello burner lockout repeats with the same blink code, a part is usually worn out. Probes, photocells, ignition electrodes, valve coils and control boxes are the usual replacements. Still, rule out supply and wiring faults first, because a control box is often changed when the real fault was elsewhere. Our guide to the Riello CMG88 62D2 control box explains when the box itself is the problem. For anything beyond basic checks, read when to call a Riello burner technician in Mumbai.
Buy Riello burner spare parts in Mumbai
Riello industrial oil and gas burners (Combustion & Control Systems) supplies Riello burner spare parts including probes, photocells, control boxes, ignition transformers, nozzles and Brahma gas solenoid valves. The business has been in burners and combustion systems since 1996.
Address: Gala No. 204, B Block, Prime Trade Center, Waliv Phata, Sativali Road, Vasai (E) – 401208, Maharashtra (Mumbai region).
If you are dealing with a Riello burner lockout, send us your burner model, a photo of the rating plate and the blink code. Get a price on WhatsApp.
Frequently asked questions
Why does my Riello burner lock out only sometimes?
Intermittent lockouts usually come from gas pressure dips, a slightly dirty probe or photocell, or a loose connector. Note when it happens; a pattern makes the cause easier to find.
How many times can I reset a Riello burner?
Riello advises no more than two consecutive resets. On the third lockout, call a technician instead of resetting again.
Can a faulty control box cause lockout?
Yes. However, check gas or oil supply, the flame sensor, ignition and wiring first, since these fail far more often.
Does swapping phase and neutral really cause lockout?
On gas burners with ionisation flame detection, yes. Riello lists inverted phase and neutral as a cause of lockout without flame detection.
Do I need a technician to fix a Riello burner lockout?
Operators can do the basic checks above. Gas train work, burner adjustment and combustion setting should be done by a qualified technician.