The Riello 40 G5 is a compact single-stage (on/off) light oil burner made in Italy. It fires between 28 and 60 kW (about 24,000 to 51,600 kcal/h) and burns roughly 2.3 to 5 kg of diesel per hour. As a result, it is a good fit for small boilers, hot water generators, ovens and dryers that need steady, reliable heat.
What is the Riello 40 G5 oil burner?
Riello makes the 40 G series of one-stage light oil burners. The series has ten models, covering outputs from 12 to 240 kW. The G5 sits at the small end of the range, above the G3 and below the G7 and G10.
Every burner in the series is fired at the factory before dispatch. So it arrives ready for installation and fine-tuning on site.
You will usually find three versions:
- G5 – the standard version, 28–60 kW.
- G5R – same output, with an oil pre-heater next to the nozzle for smoother ignition.
- G5RK – a low-output version that can go down to 12 kW.
Where is this burner used?
Because of its small size and simple on/off control, this burner works well in:
- Small hot water boilers and small steam boilers
- Hot air generators and space heaters
- Bakery ovens and small industrial ovens
- Dryers in food, textile and laundry units
- Small thermic fluid heaters
- Sites where piped gas is not available
Riello 40 G5 technical specifications
| Brand | Riello (Italy) |
| Model | 40 G5 (also G5R and G5RK) |
| Operation | Single stage (on/off) |
| Heat output | 28 – 60 kW (24.1 – 51.6 Mcal/h) |
| Fuel delivery | 2.3 – 5 kg/h |
| Fuel | Light oil / diesel |
| Testing | Emissions measured as per EN 267 |
Is this the right size for your equipment?
Always choose a burner by the heat input your boiler or oven needs. For example, a boiler that gives 45 kW at about 90% efficiency needs roughly 50 kW from the burner. That is well inside the G5 range.
However, if your equipment needs more than 60 kW, the next step up is the Riello 40 G10 oil burner (54–120 kW). Not sure which one you need? Send us a photo of your boiler or oven nameplate on WhatsApp, and we will suggest the right model.
How do you keep the burner running well?
A few simple checks prevent most breakdowns and lockouts:
- Change the nozzle once a season, or sooner if the flame looks smoky. See our Riello oil burner nozzles.
- Clean the photocell. A dirty flame sensor is a common cause of lockout. Replacement: Riello G5 / G10 / G20 photocell.
- Clean the oil filter and check the pump pressure.
- Check the ignition electrodes for wear and the correct gap.
- Keep a spare control box, such as the Riello 530SE control box, to avoid long downtime.
Buy Riello 40 G5 in Mumbai
Riello industrial oil and gas burners supplies this burner and its spare parts from Gala No. 204, B Block, Prime Trade Center, Waliv Phata, Sativali Road, Vasai (E) – 401208. We serve Mumbai, Thane, Vasai-Virar, Bhiwandi, Palghar and customers across India.
👉 View the Riello 40 G5 product page or WhatsApp us for the price.
Frequently asked questions
What is the output of this burner?
It fires from 28 to 60 kW, which is about 24,000 to 51,600 kcal/h.
Is it single stage or two stage?
It is a single-stage (on/off) burner. The G5R version adds an oil pre-heater for smoother starts.
What fuel does it use?
It runs on light oil (diesel). Tell us your fuel type before ordering so we can confirm the right setup.
What is the difference between the G5 and the G10?
The G10 is the bigger model, with 54 to 120 kW output, for larger boilers and ovens.
How do I get the price?
Message us on WhatsApp at +91 98197 08885 with your equipment details.