The Suntec TA2C oil pump is a gear-type fuel pump used on industrial burners that run on light oil, furnace oil or heavy oil. It pulls oil from the tank, raises it to the pressure the nozzle needs and sends the extra oil back to the return line. In short, if this pump fails, the burner cannot spray fuel and the boiler or furnace stops.

What does the Suntec TA2C oil pump do?
Suntec designed the TA range for industrial heating with light or heavy oils. Inside, a gear set draws oil from the tank and feeds a pressure regulating valve. The valve holds a steady pressure on the nozzle line, while any oil the nozzle does not need goes back to the tank or suction side.
The pump also has a location for a preheater. As a result, cold starts are easier when you burn thicker oils such as furnace oil.
How do you read the code TA2C 4010-7?
The code on the pump label tells you exactly which version you have:
- TA – the pump type, with built-in pressure regulation
- 2 – the gear set size, which sets the pump capacity (TA3, TA4 and TA5 are bigger)
- C – the shaft rotation direction, seen from the shaft end
- 4010-7 – the version and revision details
Because of this, always order by the full code on your old pump. A pump with the wrong rotation or gear size will not work correctly on your burner.
Key technical data
| Brand | Suntec (France) |
| Model | TA2C 4010-7 |
| Fuel | Light oil and heavy oil (one or two-pipe systems) |
| Operating viscosity | 2 – 75 cSt (heat thicker oil to bring it below 75 cSt) |
| Oil temperature in the pump | 0 – 150 °C |
| Maximum speed | 3600 rpm |
| Cross-references | Ecoflam P148 / P148/1, Oilon 340241390 |
Which burners use this pump?
You will find the TA2C, or a close relative, on many heavy oil and furnace oil burners, including:
- Ecoflam Oilflam heavy oil burners (400.1, 500.1, 700.1) and the Maior series
- Riello heavy oil burners
- Oilon GRP-M series burners
- Weishaupt, Unigas, Thermax and JN Marshall boiler burners
These burners serve steam boilers, thermic fluid heaters, furnaces and dryers across Indian industry.
What are the signs of a failing oil pump?
Watch out for these common symptoms:
- Low or unsteady nozzle pressure – the gauge reading drops or swings.
- Burner lockout or flame failure after a few seconds of running.
- Noisy pump – grinding or whining often means worn gears or air in the suction line.
- Oil leakage around the shaft seal.
- Smoky flame, because the nozzle is not getting enough pressure.
Before you replace the pump, however, check the oil filter, the suction line and the coupling. A blocked Suntec pump filter or a worn burner coupling can cause the same problems.
TA2C or TA3C: which one do you need?
The number after “TA” shows the gear size. A TA2 is the smaller capacity pump, while the Suntec TA3C and larger models suit bigger burners. Simply match the code on your old pump, or send us your burner model, and we will confirm the right size.
See it on Instagram
We shared photos of this pump and the burners it fits on our Instagram page. View the Suntec TA2C post on Instagram.
Buy the Suntec TA2C in Mumbai
Riello industrial oil and gas burners supplies Suntec oil pumps and burner spare parts from Gala No. 204, B Block, Prime Trade Center, Waliv Phata, Sativali Road, Vasai (E) – 401208. We serve Mumbai, Thane, Bhiwandi, Vasai-Virar, Palghar and customers across India.
View the Suntec TA2C product page or WhatsApp us for the price.
Frequently asked questions
Can this pump handle furnace oil?
Yes. It works with light and heavy oils, provided the oil is heated to below 75 cSt.
What does the letter C mean in TA2C?
It shows the shaft rotation direction. Always match it to your old pump.
Is it the same as the Ecoflam P148 pump?
The TA2C is listed under Ecoflam part codes P148 and P148/1. Send us your old part code to confirm.
How do I get the price?
Send the code from your old pump’s label on WhatsApp at +91 98197 08885.